STM32F303RDT6

Las imágenes son solo para referencia

STM32F303RDT6

IC MCU 32BIT 384KB FLASH 64LQFP

100% original & Nuevo

24 horas listos para el envío

Garantía de 365 días

RFQ y Obtenga más descuentos

Especificaciones

Supplier STMicroelectronics
Package Tray
Series STM32F3
ProductStatus Active
CoreProcessor ARM® Cortex®-M4
CoreSize 32-Bit Single-Core
Speed 72MHz
Connectivity CANbus, I²C, IrDA, LINbus, SPI, UART/USART, USB
Peripherals DMA, I²S, POR, PWM, WDT
NumberofI/O 51
ProgramMemorySize 384KB (384K x 8)
ProgramMemoryType FLASH
RAMSize 80K x 8
Voltage-Supply(Vcc/Vdd) 2V ~ 3.6V
DataConverters A/D 22x12b; D/A 2x12b
OscillatorType Internal
OperatingTemperature -40°C ~ 85°C (TA)
MountingType Surface Mount
Package/Case 64-LQFP

Descripción general

Description

STM32F303RDT6 is a mid‑range STM32F3 MCU from STMicroelectronics. It uses a 32‑bit ARM Cortex‑M4F core with DSP/FPU, optimized for fast control and signal processing tasks. It runs up to about 72 MHz and includes on‑chip Flash and RAM, plus rich mixed‑signal peripherals.
In the 64‑pin LQFP variant (RDT6), you typically get:
- 12‑bit ADCs, 12‑bit DACs, and analog front‑ends (comparators/op-amps)
- multiple timers (including advanced motor-control timers) and PWM
- memory: on‑chip Flash and RAM (sizes vary by exact part)
- communications: USART/UART, I2C, SPI, USB FS on supported devices, and CAN on some variants
- DMA, CRC, and power-management features
Commonly used for motor control, power electronics, sensor processing, audio, and mixed-signal applications. Supply voltage ~2.0–3.6 V; multiple low‑power modes are available.
Development workflow: STM32CubeMX for configuration, HAL/LL libraries, and standard IDEs (Keil, IAR, STM32CubeIDE). Always verify exact Flash/RAM and peripherals from the specific datasheet for F303RDT6.

Features

STM32F303RDT6 features (summary)
- CPU: 32‑bit ARM Cortex‑M4F with DSP and single‑precision FPU; up to 72 MHz.
- Memory (depends on package): on‑chip Flash up to ~256 KB; RAM up to ~40 KB.
- Peripherals: USB 2.0 Full‑Speed device; CAN 2.0B; multiple serial interfaces (USART/UART, SPI, I2C); up to 16‑channel, 12‑bit ADC; several timers including an advanced TIM1.
- DMA and memory: DMA controller; CRC hardware unit; MPU for memory protection.
- Clocks and power: HSI/HSE with PLL; operating voltage 2.0–3.6 V; wake/low‑power modes (sleep, stop, standby).
- Debug/boot: SWD/JTAG, built‑in bootloader.
- Extras: operating temperature typically −40 to 85 °C (industrial); package: LQFP64 in the RDT6 variant (other packages available).
Notes: exact Flash/RAM sizes and available peripherals depend on the specific package/pinout. Check the datasheet for the exact figures for STM32F303RDT6.

Package

LQFP-48 package (48-pin, 7x7 mm).

Pinout

- Pin count: 100 pins (LQFP-100 package)
- Function: 32-bit ARM Cortex-M4 microcontroller (STM32F3 family) for embedded applications with integrated peripherals.

Manufacturer

- Manufacturer: STMicroelectronics (STMicro).
- What kind of company: A global semiconductor company that designs, develops, and manufactures integrated circuits and microelectronics (including the STM32 microcontroller family) for automotive, industrial, and consumer markets. Headquarters in Geneva, Switzerland, with operations worldwide.

Application

STM32F303RDT6 is a Cortex-M4 MCU with DSP/FPU for mixed-signal control. Typical applications:
- Motor control (BLDC/PMSM, FOC)
- Power electronics and digital power supplies
- Industrial automation and process control
- Data acquisition and instrumentation (sensor interfaces)
- Audio and DSP processing
- USB-enabled devices
- Automotive body electronics and sensors

Equivalent

Closest equivalents:
- Within ST (same MCU family, different package): STM32F303RET6, STM32F303RBT6 (and other F303RxxT6 variants).
- Cross-vendor (Cortex-M4F with USB/ADCs and similar memory): TI TM4C123GH6PM, NXP LPC4088, Microchip ATSAME53N20A.
Note: exact flash/RAM counts and peripherals differ; consult datasheets and cross-reference tables for pin/package match.

Envío

Métodos de envíoNosotros

ofrecer servicios de envío globales a través de DHL, FedEx, TNT, UPS, o cualquier otro expediente de su elección.


Referencia de tarifas de envío (DHL/FedEx):

DHL: El costo de envío oscila entre $25-$45 (0.5kg), con un tiempo de entrega estimado de 2-5 días hábiles.

FedEx: El costo de envío oscila entre $25-$40 (0.5kg), con un tiempo de entrega estimado de 3-7 días hábiles.

UPS: El costo de envío oscila entre $25-$45 (0.5kg), con un tiempo de entrega estimado de 3-7 días hábiles.

TNT: El costo de envío oscila entre $25-$65 (0.5kg), con un tiempo de entrega estimado de 3-7 días hábiles.

EMS: El costo de envío oscila entre $30-$50 (0.5kg), con un plazo de entrega estimado de 7-15 días hábiles.

Correo aéreo registrado: El costo de envío es de $2-$4 (0.1kg), con un tiempo de entrega estimado de 5-20 días hábiles.

Pagos

Payment Methods

El plazo de pago es 100% prepagado.

Actualmente, solo aceptamos los siguientes métodos de pago:

1. de PayPal

2. Tarjeta de crédito/débito

3. Transferencia bancaria

Similar