OPB625

Las imágenes son solo para referencia

OPB625

SENSOR OPTICAL 4.83MM PCB MOUNT

  • Fabricante
  • Mfr. Parte #OPB625
  • Paquete
  • Hoja de datos
  • En stock8382

100% original & Nuevo

24 horas listos para el envío

Garantía de 365 días

RFQ y Obtenga más descuentos

Especificaciones

Series Photologic®
Part Status Active
Sensing Distance 0.190" (4.83mm)
Sensing Method Through-Beam
Output Configuration Pull-Up Resistor, Buffer
Mounting Type Through Hole
Current - Supply 12 mA
Voltage - Supply 4.5V ~ 16V
Response Time 30ns
Operating Temperature -40°C ~ 100°C
Package PCB Mount
Packaging Bulk

Descripción general

Description

OPB625 is an optocoupler (optoisolator) with an infrared LED input and a phototransistor output. It provides galvanic isolation between a low-voltage control side and a high-voltage/noisy side, letting a logic signal control a circuit without a shared ground. When the LED is driven, light activates the transistor, allowing current to flow on the output side.
Key points:
- Package: typically 4-pin DIP (variants exist). Pinout usually: pin 1 anode, pin 2 cathode, pin 3 emitter, pin 4 collector (verify in the datasheet).
- Isolation: several kilovolts RMS between input and output.
- CTR: current transfer ratio depends on LED current and temperature; specified in the datasheet.
- Speed: suitable for low- to moderate-speed signaling (tens to thousands of Hz, depending on variant).
Common uses: microcontroller or PLC signal isolation, SMPS control, sensing where galvanic isolation is needed.
For exact electrical specs (IF, CTR, VCE(sat), tPHL/tPLH) and packaging variants, consult the OPB625 datasheet.

Features

OPB625 is a phototransistor optocoupler (optoisolator). Key features (typical; variant-dependent):
- Isolation: ~5 kV RMS between input LED and output transistor
- CTR: roughly 50–300% at IF = 20 mA (up to 600% max, depending on variant and temperature)
- Input: Infrared LED, IF ≈ 20 mA, Vf ≈ 1.2 V
- Output: NPN phototransistor (max IC ~50 mA)
- Speed: standard (not high‑speed); t_r/t_f in the μs range
- Package: DIP‑4 or similar SMD variants
- Operating temp: typically −40 to +85 °C (industrial); wider on some versions
- Applications: galvanic isolation for logic/data signals, microcontroller interfacing, safety-critical isolation
Note: exact numbers (CTR, VCEO, speed) vary by variant (e.g., OPB625A/B). Check the specific datasheet for precise specs.

Package

OPB625 is a single-channel optocoupler packaged in a standard 4-pin DIP (through-hole) package.

Pinout

OPB625 is a 4‑pin DIP optocoupler (optical isolator). It has an input LED and a phototransistor output, providing isolation between input and output.
Pinout (typical):
- Pin 1: Anode
- Pin 2: Cathode
- Pin 3: Emitter
- Pin 4: Collector
The LED (pins 1–2) drives the phototransistor (pins 3–4) to transfer a signal across isolation.

Manufacturer

OPB625 is manufactured by OPTEK Technology. OPTEK is an optoelectronics company that designs and manufactures optocouplers, phototransistors, LEDs, and other optical/electrical components.

Application

OPB625 is a phototransistor-output optocoupler. Applications include galvanic isolation between low-voltage logic and high-voltage/noisy circuits; interfacing microcontrollers with power electronics; feedback and sensing in switching power supplies; driving relays/triacs and motor drivers; signal isolation in automation/PLC I/O and data communication interfaces; instrumentation and safety-critical equipment requiring isolation.

Equivalent

OPB625 is a phototransistor optocoupler. Common equivalents/substitutes with similar CTR and specs include: PC817, EL817, 4N25, 4N35, LTV-817, SFH618A, FOD817A. Ensure you match CTR, Vceo/isolation voltage, and package to your design from the datasheets.

Envío

Métodos de envíoNosotros

ofrecer servicios de envío globales a través de DHL, FedEx, TNT, UPS, o cualquier otro expediente de su elección.


Referencia de tarifas de envío (DHL/FedEx):

DHL: El costo de envío oscila entre $25-$45 (0.5kg), con un tiempo de entrega estimado de 2-5 días hábiles.

FedEx: El costo de envío oscila entre $25-$40 (0.5kg), con un tiempo de entrega estimado de 3-7 días hábiles.

UPS: El costo de envío oscila entre $25-$45 (0.5kg), con un tiempo de entrega estimado de 3-7 días hábiles.

TNT: El costo de envío oscila entre $25-$65 (0.5kg), con un tiempo de entrega estimado de 3-7 días hábiles.

EMS: El costo de envío oscila entre $30-$50 (0.5kg), con un plazo de entrega estimado de 7-15 días hábiles.

Correo aéreo registrado: El costo de envío es de $2-$4 (0.1kg), con un tiempo de entrega estimado de 5-20 días hábiles.

Pagos

Payment Methods

El plazo de pago es 100% prepagado.

Actualmente, solo aceptamos los siguientes métodos de pago:

1. de PayPal

2. Tarjeta de crédito/débito

3. Transferencia bancaria

Similar